Teradek Bolt 500 XT SDI/HDMI Wireless Deluxe Kit (Gold Mount)  main

Teradek Bolt 500 XT SDI/HDMI Wireless Deluxe Kit (Gold Mount)

This product has been discontinued.

We have discontinued this product permanently. Please find alternative products from below section.

Teradek Bolt 500 XT SDI/HDMI Wireless Deluxe Kit (Gold Mount)

  • 3D LUTs, 5GHz spectrum analyzer
  • 3G-SDI/HDMI Input & 3G-SDI Loop-Out
  • Dual 3G-SDI Outputs & 1x HDMI Output
  • Up to 500' Range Line of Sight
  • AES128 Encryption & Zero Delay
  • 2.4 & 5.8 GHz Noise Rejection
  • Supports up to 1080p60 Resolution

The Bolt 500 XT SDI/HDMI Wireless TX/RX Deluxe Kit includes one Transmitter and one Receiver with installed (Gold-Mount) and a variety of accessories. The Bolt 500LT allows you to transmit up to 1080p60 video signal from either an SDI source. The zero-latency transmitter/receiver pair features a 500' line-of-site transmission distance when used together. You can send and receive visually lossless 3G-video signals from a Bolt 500 transmitter with zero latency.

Teradek Bolt 500 XT 3G-SDI/HDMI Wireless Transmitter
Teradek Bolt 500 XT 3G-SDI/HDMI Wireless Transmitter allows you to visually lossless 3G video signals to a Bolt 500 receiver with zero latency. The Bolt XT is compatible with existing third-generation Bolt systems such as the Bolt 500, 1000, Sidekick II, and 703 Bolt, as well as the Bolt LT. This Transmitter features an HDMI, 3G-SDI and looping 3G-SDI output. Unlike alternative wireless video systems, Bolt XT includes AES 128 encryption algorithm to protect your video footage, ensuring that only authorized receivers can connect to your transmitter.

The Bolt 500 XT is made of aluminum chassis to reduces the size and weight of the Bolt, with receivers also allowing for integrated pass-through power. Available battery plate accessories include V- or Gold-mount, in addition to bi-directional Sony L-series or Canon LP-E6 plates on the Bolt 500 XT. Teradek has also replaced the internal antennas on the Bolt 500 XT transmitter with an external set to enhance wireless performance when operating in environments with large obstacles or heavy interference.

Bolt 500 XT Transmitter features:
• Compatible with 3rd generation Bolt 500, Bolt 500 LT, Sidekick II, Focus Bolt RX, and 703 Bolt
• Professional software features: 3D LUTs, 5GHz spectrum analyzer
• Smaller and lighter chassis design with robust mounting points (3/8” and ¼”-20)
• Dual input (SDI + HDMI) and SDI loop out

Teradek Bolt 500 XT 3G-SDI/HDMI Wireless Receiver
The Teradek Bolt 500 XT 3G-SDI/HDMI Wireless Receiver you can receive visually lossless 3G-video or HDMI signals from a Bolt 500 transmitter with zero latency. The Bolt XT is compatible with existing third-generation Bolt systems such as the Bolt 500, 1000, Sidekick II, and 703 Bolt, as well as the Bolt LT. The Bolt XT Receiver features an HDMI output as well as dual 3G-SDI outputs. While wireless performance is critical on set, so are practical mounting options that ensure optimal performance and a quick set-up. Teradek integrated a NATO rail on the receiver, several 1/4”-20 and 3/8” mounting points.

Bolt 500 XT Receiver Features:
• Compatible with 3rd generation Bolt 500, Bolt 500 LT, and Focus Bolt TX
• Professional software features: 3D LUTs, 5GHz spectrum analyzer
• HDMI and Dual 3G-SDI outputs

Wooden Camera Ultra Arm Mini Monitor Mount (1/4"-20 to 1/4"-20)
The Wooden Camera Ultra Arm Mini Monitor Mount is an articulating arm with tool-less 1/4-20 knobs and non-slip rubber pads on each end and a center double ball clamp. This is a shorter version of the Ultra Arm and is ideal for keeping your LCD or accessory close to the camera body while still achieving a good range of motion.

The Ultra Arm components are interchangeable so you can use this arm in conjunction with the other options we make like 3/8-16, NATO Clamp, Hot Shoe, and Super Clamp. You can also add a center extension piece and second Double Ball Clamp! Many existing 3rd party 25mm ball systems are compatible as well.

Wooden Camera NATO Lock Kit
The NATO Lock Kit is a quick release set based on a NATO standard rail. The rail portion can bolt into a 1/4-20 or 3/8-16 hole using the included screws. Set screw can also be installed to prevent twisting. The rail is also threaded for 1/4-20 and 3/8-16 so accessories can screw into it.

The clamp portion of the kit can also bolt into a 1/4-20 or 3/8-16 hole using the included screws and it is also threaded for 1/4-20 and 3/8-16 so accessories can screw into.

 

More Information
 
   
In the box Teradek Bolt 500 XT 3G-SDI/HDMI Wireless Transmitter
Teradek Bolt 500 XT 3G-SDI/HDMI Wireless Receiver
1 x Protective SKB Case 
1 x Wooden Camera Ultra Arm Mini Monitor Mount (1/4-20 to 1/4-20)
1 x Wooden Camera NATO Lock Kit
1 x Teradek Vinyl Zipper Bag 250x150mm
1 x Hex L Key 2.5 mm size 3-5/6 inch length
1 x Hex L key 3/16inch x 2 13/16inch length
1 x factory-installed Gold Mount (female) Battery Plate 14.4V attached to RX
1 x 2-Pin Connector to PowerTap 18 inch Cable
1 x Hot Shoe Adapter (1/4"-20 inch)
2 x Antenna 2dBi WiFi 2.4/5.8 GHz
1 x USB 2.0 Cable (A-Male to Mini-B)
1 x HDMI 18in Cable (Type A to Type A)
1 x SDI (BNC to BNC) Cable 10 inch
1 x Lightstand Adapter (1/4"-20 inch)
1 x USB 2.0 Cable (A-Male to Mini-B)
1 x PSU 2-Pin Connector to 18W AC Adapter 6ft cable
1 x HDMI 18in Cable (Type A to Type A)
1 x SDI (BNC to BNC) Cable 10 inch
Limited 1-year warranty
  Teradek Bolt 500 XT 3G-SDI/HDMI Wireless Transmitter
Video Interface  
Video Inputs 1 x SD/HD/3G-SDI (75 Ohm BNC)
1 x Type A receptacle HDMI
Video Outputs 1 x HD/SD/3G-SDI Loop-out (75 Ohm BNC)
Sdi Ancillary Data Support supports metadata, timecode, and start/stop flags from certain camera manufacturers. 
Please refer to: https://support.teradek.com/hc/en-us/articles/217446087
Color Sampling SDI: YCbCr 4:2:2, 8-bit HDMI: RGB 4:4:4, 8-bit
Delay Tx To Rx <0.001sec (without format conversion)
Supported Resolutions 1080p 23.98/24/25/29.97/30/50/59.94/60
1080psf23.98/24/25/29.97/30
1080i50/59.94/60
720p50/59.94/60
480p59.94/576p50 (via HDMI ports only)
480i(NTSC)/576i(PAL)
Video Compression Visually lossless
Video Format Conversion Support Yes
Color Correction CDL/1024 1D LUT (supports 10-bit color)
33x33x33 3D LUT (supports 10-bit color)
Audio Compression 48kHz 24-bit PCM
Audio Input Embedded Audio Input
   
Physical  
Dimensions 0.95" x 2.6" x 4.47
Weight 8oz (226g)
Construction Milled Aluminum(Chassis) and regulation-compliant PCB
Mountability Multiple mounting options with M3 and 1/4" holes 3/8" ARRI style accessory mount
   
Interfaces  
Http None
Configuration Interfaces None
Switches On/Off and Reset Switch
Desktop App Feature-rich Bolt Manager Application for OSX & Windows
Usb Interface Functionality Upgrade via Mini-USB
Wireless Non-DFS Frequencies:
US: 5.19 ~ 5.23 GHz and 5.755 ~ 5.795 GHz
EU & JP: 5.19 ~ 5.23 GHz
DFS Frequencies:
US: 5.27 ~ 5.55 GHz and 5.67 GHz
EU & JP: 5.27 ~ 5.67 GHz
Rf Channel Selection Auto only (NOT configurable)
Encryption AES-128
Rf Power 17dBm EIRP
Range Up to 500ft line of sight
Unicast Multicast Unicast / Multicast
Noise Rejection Can coexist with WiFi and 5GHz cordless phones
   
Power  
Power Input 2-Pin Connector 7-28 VDC
Battery None
Nominal Power Consumption 7.3 Watts (Measured at 1080p60)
   
Environmental  Operating Temperature :0 ~ 40 deg-C
   
  Teradek Bolt 500 XT 3G-SDI/HDMI Wireless Receiver
Video Interface  
Video Outputs 1 x SD/HD/3G-SDI (75 Ohm BNC)
1 x HDMI Type-A receptacle
Sdi Ancillary Data Support Supports metadata, timecode, and start/stop flags from certain camera manufacturers.
Please refer to: https://support.teradek.com/hc/en-us/articles/217446087
Color SamplingColor Sampling SDI: YCbCr 4:2:2, 8-bit HDMI: RGB 4:4:4, 8-bit
Delay Tx To Rx <0.001sec (without format conversion)
Supported Resolutions 1080p 23.98/24/25/29.97/30/50/59.94/60
1080psf23.98/24/25/29.97/30
1080i50/59.94/60
720p50/59.94/60
480p59.94/576p50 (via HDMI ports only)
480i(NTSC)/576i(PAL)
Video Compression visually lossless
Test Pattern Generator Support Yes
Video Format Conversion Support Yes
Color Correction 1024 1D LUT 17x17x17 3D LUT
Audio Compression 48kHz 24-bit PCM
Audio Input Embedded Audio Input
   
Physical  
Dimensions 6" x 3.4" x 1"
Weight 10.5oz(299g)
Construction Milled Aluminum(Chassis) and regulation-compliant PCB Plastic Cap
Mountability Multiple mounting options with M3 and 1/4" holes
   
Interfaces  
Http None
Configuration Interfaces OLED Screen with Menu Joystick Navigation
Desktop App Feature-rich Bolt Manager Application for OSX & Windows
Usb Interface Functionality Upgrade via Mini-USB
Wireless Non-DFS Frequencies:
US: 5.19 ~ 5.23 GHz and 5.755 ~ 5.795 GHz
EU & JP: 5.19 ~ 5.23 GHz
DFS Frequencies:
US: 5.27 ~ 5.55 GHz and 5.67 GHz
EU & JP: 5.27 ~ 5.67 GHz
Rf Channel Selection Auto only (NOT configurable)
Encryption AES-128
Rf Power 15dBm EIRP
Range Up to 500ft line of sight
Unicast Multicast Unicast / Multicast
Noise Rejection Can coexist with WiFi and 5GHz cordless phones
   
Power  
Power Input 2-Pin Connector 7-28 VDC
Battery None
Nominal Power Consumption 9 Watts (Measured at 1080p60)
Environmental  Operating Temperature: 0~ 40 deg-C
Write Your Own Review
You're reviewing:Teradek Bolt 500 XT SDI/HDMI Wireless Deluxe Kit (Gold Mount)
Your Rating
Customer Questions
No Questions
Please, mind that only logged in users can submit questions